Sale!

EXP-10000

 1,000,000

Deep Search

Description

 EPX 10000 Deep Depth Long Range

Underground Gold Treasure Hunter 50M with Degausser

New Version Digital Frequency Synthesis Radar Remote Detector Underground Metal Detector gold Diamond Silver Copper Metal Detector exp10000 Long Range King is ‘custom built’ in a sturdy, hard side, padded case with two locks. The transmitter is case mounted and includes the ‘Standard Seven’ elements with selector switch. The system includes an installed, rechargeable gel cell battery with charger, transmitting antenna, receiving rods and receiver with belt clip, headphones and user manual all inserted into the specially fitted case.

 

 

Technical parameters :

  1. Voltage:12VDC
  2. Humidity:0~95%
  3. Thtemperaure range:45 to 85
  4. Detection depth range:5-50m
  5. Detection distan cerange :100-1000m
  6. 7.16 bit processor speed,40MIPS –16MHz
  7. 32 bit DSS synthesis chip,wave from output
  8. Rechargeable battery:8 hours of continuous work
  9. .Color LCD display,a resolution of 480 x 320 pixels
  10. Digital frequency synthesisX20PLL,automatic frequency stabilizer,0.1MHz

INSTALLATION :

Scanner control installation
Note: Before the daily operation, the battery must be fully charged! If you do not charge it, the EPX10000 might go wrong. If abnormal , this may be the first time warning that  the battery power is too low and must be charged. If the battery power is charged a whole night, after that, the battery is still no power, you need to replace the battery or charger, or AC power outlet without electricity. If the battery is charged,but it is not full of power,you may need to replace the built-in battery. A new fully charged battery can let EPX10000 continue to work about eight hours.
Before turning on the scanner, put the EPX10000 transmitter on the ground, the sensor antenna is connected to the corresponding jacks of the transmitter. When open the transmitter,never plug the sensor, if doing it, it will cause damage to the machine.
Previously used EPX10000 scan,first make all the necessary connections.
1.The sensor is connected to the scanner testing (+) testing (-) on the jack, insert the probe of sensor on the earth
2.The transmit antenna signal transmission is mounted on the corresponding interface
3. with the power key is turned “On / Off” knob, turn on the power. At this time, in the LCD area, power indicator,horizontal trmming,longitudinal trmming indicator lights.
4. at this time, EPX10000 is scanning all selected element . Before starting the detection process, please let it work 3-5 minutes, which will be briefly explained later.
5.after the end of the operation, remember to turn off EPX10000. For ease to use,the instrument requires the use of a smll battery charger is connected to the power line charg instrument.
Receiver – The rotary switch on the top of the receiver panel are the headphone and the antenna jack. When do not use, do not connect the antenna rods with  the receiver! If the antenna rod is saved with it inserted in the receiver , it will cause the battery to drain.
Receiving antenna rod – rod antenna is designed to point out to the operator that he / she has entered a power transmission line between the sensor and the target. Under normal circumstances, the operator should hand held the antenna rod stably and balanced, as high as your waist, and slightly in front of the operator. When hand held the antenna rods, rod antenna should is pointed to the front and parallel to each other and separated by 8-18 inches away. Everyone needs to find their own best distance. It takes trial and error to find. Please remember, the people who operate this device, calm relaxed person  will do better than the tense stiff! When you enter the RF energy line, measured metal,the antenna rod will naturally cross.

And the radar scan pointer will stop in one location. When the antenna and radar cross and the scanner pause, you see the dawn of victory would come.

Package :

  • Qty./CTN: 1unit
  • G.W./CTN: 10.5kg
  • Weight/Unit: 6.6 kg
  • Size/Unit: 47X37X13.5cm